kelleherdwyer9

kelleherdwyer9

ผู้เยี่ยมชม

  Cisco CCNP/ BCMSN Check Tutorial: Static VLANs (4 อ่าน)

12 พ.ย. 2569 03:23

BCMSN test outcomes and earning your CCNP accreditation needs you to increase to your understanding of VLAN configuration. When you analyzed for your CCNA test, you uncovered procedures to spot ports into a VLAN and what the reason of VLANs was, getting stated that you may possibly potentially not notice that there are two varieties of VLAN membership. To go the BCMSN take a look at, you want to understand the information of both kinds.

In this tutorial, we are going to take into consideration an in general search at the VLAN sort you are most popular with, the "preset VLAN". Host gizmos relevant to a port belonging to just one particular VLAN will purchase broadcasts and multicasts only if they ended up occur from by an further host in that amazingly exact VLAN.

bulk cargo boxes of a set VLAN is typical loads of. In this circumstance in point, by positioning adjust ports /one particular and /2 into VLAN twelve, the only broadcasts and multicasts hosts joined to folks ports will get are the kinds transmitted by ports in VLAN 12.

SW1( config) #int swift /a single

SW1( config-if) #switchport method entry

SW1( config-if) #switchport access vlan 12

% Entry VLAN does not exist. Establishing vlan twelve

SW1( config-if) #int rapidly /two

SW1( config-if) #switchport fashion entry

SW1( config-if) #switchport entry vlan twelve

Amid the quite a couple of points I like about Cisco routers and switches is that if you have really neglected to do a little anything, the Cisco gadget is typically heading to remind you or in this scenario seriously do it for you. I place port /a person into a VLAN that did not but exist, so the change developed it for me!

The problem is that a trunk port belongs to all VLANs by default, and we want to place this port into a single VLAN only. To do so, we operate the switchport method entry command to make the port an accessibility port, and accessibility ports belong to one and just 1 VLAN. Subsequent carrying out that, we place the port into VLAN twelve with the switchport accessibility vlan twelve command.

The hosts are uninformed of VLANs they only believe the VLAN membership of the port they are connected to. Yet that's not truly the state of affairs with lively VLANs, which we will study in the following portion of this BCMSN tutorial.

When you examined for your CCNA analysis, you observed out how to place ports into a VLAN and what the function of VLANs was, but you could not be aware that there are two types of VLAN subscription. In this tutorial, we will purchase a look at the VLAN form you are most common with, the "preset VLAN". Host equipment related to a port belonging to a person particular VLAN will get broadcasts and multicasts just if they have been currently being originated by an added host in that rather very similar VLAN. The challenge is that a trunk port belongs to all VLANs by default, and we want to area this port into a solitary VLAN just. Right after carrying out that, we set the port into VLAN twelve with the switchport entry vlan twelve command.

kelleherdwyer9

kelleherdwyer9

ผู้เยี่ยมชม

ตอบกระทู้
เว็บไซต์นี้มีการใช้งานคุกกี้ เพื่อเพิ่มประสิทธิภาพและประสบการณ์ที่ดีในการใช้งานเว็บไซต์ของท่าน ท่านสามารถอ่านรายละเอียดเพิ่มเติมได้ที่ นโยบายความเป็นส่วนตัว  และ  นโยบายคุกกี้